---
title: Preseem Appliance Configuration
description: Use the following procedure when an upstream firewall does not protect management access. Keep console access and your current management session open until testing is complete.
---

[Skip to content](https://docs.preseem.com/configuration/firewall-configuration#main-content)

English

Show submenu for translations

[![Preseem Logo Classic](https://docs.preseem.com/hs-fs/hubfs/Preseem%20Logo%20Classic.png?width=150&height=38&name=Preseem%20Logo%20Classic.png)](https://app.preseem.com)

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)

Open main navigation

Close main navigation

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)
- English
  
  Show submenu for translations
- Contact us

 Contact us

 Hi There! How Can We Help You?

- There are no suggestions because the search field is empty.

1. [Help Center](https://docs.preseem.com/?hsLang=en)
2. [Configuration](https://docs.preseem.com/configuration?hsLang=en)

# Preseem Appliance Configuration

Use the following procedure when an upstream firewall does not protect management access. Keep console access and your current management session open until testing is complete.

This method uses the trusted zone, which allows all listening services from the listed sources. If you need to allow only specific services, use an upstream firewall or a dedicated local policy.

**Review the current configuration**

 1\. Check whether firewalld is running:

```
systemctl is-active firewalld
```

Continue only if the result is active. If it is inactive, failed, or not installed, ask Support to review the appliance before enabling it.

 2\. Review the active zones, default zone, and existing rules:

```
sudo firewall-cmd --get-active-zonessudo firewall-cmd --get-default-zonesudo firewall-cmd --list-all-zones
```

**Allow management access**

 3\. Add the support addresses and your management subnet. Replace \<management-subnet/CIDR\> with the source network seen by the appliance, accounting for any address translation:

```
sudo firewall-cmd --zone=trusted --add-source=35.199.29.237/32sudo firewall-cmd --zone=trusted --add-source=35.197.73.77/32sudo firewall-cmd --zone=trusted --add-source="<management-subnet/CIDR>"
```

4\. Check the trusted zone. It should contain only approved management and support sources; do not assign a public-facing interface or an untrusted network to it.

```
sudo firewall-cmd --zone=trusted --list-all
```

**Block other management access**

 5\. Identify the zone used by other traffic arriving on the management interface. Check interface and source bindings in the output below. An interface without an assigned zone uses the default zone.

```
sudo firewall-cmd --list-all-zones
```

Use that zone name for \<untrusted-zone\>. If source rules or policies make the match unclear, have your network administrator identify it before continuing.

 6\. Remove the SSH and Cockpit service allowances from that zone:

```
sudo firewall-cmd --zone="<untrusted-zone>" --remove-service=sshsudo firewall-cmd --zone="<untrusted-zone>" --remove-service=cockpit
```

Also remove any unneeded explicit port or rich rules that allow the same access. If the zone accepts all traffic, removing service allowances will not block access; correct that policy first.

**Test and save**

7\. Open a new SSH session from an allowed source, then test that a connection from an unapproved source fails. Test Cockpit if used, and both IPv4 and IPv6 where enabled. Check that subscriber traffic and polling still work.

8\. Save only after the tests pass. This command saves every pending runtime firewall change, so review those changes first:

```
sudo firewall-cmd --runtime-to-permanent
```

 9\. Compare the saved and running rules. Source ranges, zone targets, and service allowances should match:

```
sudo firewall-cmd --permanent --list-all-zonessudo firewall-cmd --list-all-zones
```

If a test fails, correct the running rules from the console and repeat the test before saving. Do not reboot to recover access. See [Preseem Firewall Configuration](https://docs.preseem.com/how-do-i-configure-a-firewall-for-my-preseem-element?hsLang=en) for more information.

### **Firewall Configuration Checklist**

- The upstream firewall or local firewalld policy is active; local changes are saved if used.
- Approved sources can open new management sessions; unapproved sources cannot.
- IPv4 and IPv6 are covered where used, and trusted-zone sources have been reviewed.
- Subscriber traffic forwards normally, and polling data continues to update.

- [Preseem Overview](https://docs.preseem.com/preseem-overview?hsLang=en#main-content)

    - [Deployment Models](https://docs.preseem.com/preseem-overview?hsLang=en#deployment-models)
- [Preseem Hardware](https://docs.preseem.com/preseem-hardware?hsLang=en#main-content)

    - [Legacy Hardware](https://docs.preseem.com/preseem-hardware?hsLang=en#legacy-hardware)
- [Installation & Activation](https://docs.preseem.com/installation-activation?hsLang=en)
- [Configuration](https://docs.preseem.com/configuration?hsLang=en)
- [Using Preseem](https://docs.preseem.com/using-preseem?hsLang=en#main-content)

    - [How to Use Preseem to Troubleshoot Subscriber Issues](https://docs.preseem.com/using-preseem?hsLang=en#how-to-use-preseem-to-troubleshoot-subscriber-issues)
    - [Operations](https://docs.preseem.com/using-preseem?hsLang=en#operations)
    - [How to Use Preseem to Optimize QoE](https://docs.preseem.com/using-preseem?hsLang=en#how-to-use-preseem-to-optimize-qoe)
    - [Preseem's RF Scoring and Metrics](https://docs.preseem.com/using-preseem?hsLang=en#preseems-rf-scoring-and-metrics)
- [Administering Preseem](https://docs.preseem.com/administering-preseem?hsLang=en#main-content)

    - [Upgrades](https://docs.preseem.com/administering-preseem?hsLang=en#upgrades)
    - [Planning and Configuration](https://docs.preseem.com/administering-preseem?hsLang=en#planning-and-configuration)
    - [Troubleshooting](https://docs.preseem.com/administering-preseem?hsLang=en#troubleshooting)
    - [User Management](https://docs.preseem.com/administering-preseem?hsLang=en#user-management)
- [Integrations](https://docs.preseem.com/integrations?hsLang=en)
- [FAQs and Other Explanations](https://docs.preseem.com/faqs-and-other-explanations?hsLang=en)
- [Amplify AI - Support Assistant](https://docs.preseem.com/amplify-ai-support-assistant?hsLang=en)

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)

[![Chill listening crop-3](https://docs.preseem.com/hs-fs/hubfs/Preseem_logo_large.png?width=80&height=30&name=Preseem_logo_large.png "Chill listening crop-3")](https://preseem.com/)

Copyright © 2026, Preseem (Aterlo Networks)