---
title: Physical Installation
description: How to connect to the Preseem appliance using console, SSH or Cockpit
---

[Skip to content](https://docs.preseem.com/installation/physical-installation#main-content)

English

Show submenu for translations

[![Preseem Logo Classic](https://docs.preseem.com/hs-fs/hubfs/Preseem%20Logo%20Classic.png?width=150&height=38&name=Preseem%20Logo%20Classic.png)](https://app.preseem.com)

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)

Open main navigation

Close main navigation

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)
- English
  
  Show submenu for translations
- Contact us

 Contact us

 Hi There! How Can We Help You?

- There are no suggestions because the search field is empty.

1. [Help Center](https://docs.preseem.com/?hsLang=en)
2. [Installation & Activation](https://docs.preseem.com/installation-activation?hsLang=en)

# Physical Installation

- Verify that rack space, power, and cabling align with the topology plan from Section 3.
- Install compatible transceivers on both the Preseem appliance and the connected router or switch (see Section 2).
- Connect the management interface and both bridge interfaces before powering on the device.

**![](https://docs.preseem.com/hs-fs/hubfs/undefined-Nov-06-2026-01-17-41-2212-AM.png?width=670&height=208&name=undefined-Nov-06-2026-01-17-41-2212-AM.png)**

*Image 1:* Diagram showing management, bridge, and console port locations

**Initial Connectivity**

There are three supported ways to reach the appliance for initial, OS-level configuration:

- **Serial console:** Works even before the appliance has network connectivity. This is the most reliable option for first-time commissioning.
- **SSH:** Available on standard port 22 once the management interface has an IP address.
- **Cockpit:** Fedora's web-based administration interface, accessible via HTTPS at **https://\<appliance management IP\>:9090** once network connectivity is established.

**Connect via Serial Console**

Use this method for first-time commissioning or when the appliance has no network access yet.

***\[Note:*** *The appliance ships with a USB console cable (RJ-45 end to the appliance, USB end to your laptop), and a card with default login credentials that outlines the default configuration of the management ports. If the card is missing, contact Preseem support.****\]***

1. Insert the RJ-45 end of the console cable into the appliance's **Console** port.
2. Insert the USB end into your laptop.
   
   ![](https://docs.preseem.com/hs-fs/hubfs/undefined-Nov-06-2026-01-17-40-9247-AM.png?width=418&height=324&name=undefined-Nov-06-2026-01-17-40-9247-AM.png)   
                                  *Image 2:* Console port (and to the laptop's USB port)
3. Identify the serial (COM) port assigned to the adapter on your laptop. On Windows, verify this in **Device Manager**.
   
   ![](https://docs.preseem.com/hs-fs/hubfs/image-png-Nov-16-2026-08-33-30-9658-PM.png?width=368&height=514&name=image-png-Nov-16-2026-08-33-30-9658-PM.png)  
                      *Image 3:* Windows Device Manager showing the assigned COM port
4. Open a serial terminal program (for example, PuTTY). Set the connection type to **Serial**, the speed to **115200 bps**, and select the COM port from step 3.
   
   **![](https://docs.preseem.com/hs-fs/hubfs/undefined-Nov-06-2026-01-17-40-2258-AM.png?width=406&height=353&name=undefined-Nov-06-2026-01-17-40-2258-AM.png)**  
            *Image 4:* PuTTY serial session configuration (speed and COM port fields)
5. Click **Open** to start the terminal session.
6. At the login prompt, enter your username and password from the appliance card.
7. Refer to Section 5 for instructions on configuring a static IP address.

***\[Tip:*** *If nothing appears in the terminal window, confirm the speed is set to 115200 bps and that you selected the correct COM port.****\]***

**Connect via SSH or Cockpit**

Once an IP address is configured on the management interface, connect using one of the following methods:

- **SSH**: Connect to the management IP on port 22.
- **Cockpit**: Browse to **https://\<appliance management IP\>:9090**.

**Connecting the Appliance to the Internet**

The appliance requires outbound Internet connectivity to communicate with Preseem Cloud and to allow Preseem support to complete the activation process.

- The appliance ships with two management interfaces. By default, one is set to DHCP, and the other has a static IP address. See image under *Physical Installation* in this section
- If DHCP is available on site, use the DHCP-configured interface for initial access.
- If DHCP is unavailable, configure your laptop on the same subnet as the static interface to connect via SSH or Cockpit.

***\[Caution:*** *Preseem strongly recommends using a static IP address on the active management interface for production deployments. A common approach is to log in via the serial console or DHCP interface, then reconfigure the static interface with the IP address required for deployment. Alternatively, configure a static DHCP reservation on your router.****\]***

- [Preseem Overview](https://docs.preseem.com/preseem-overview?hsLang=en#main-content)

    - [Deployment Models](https://docs.preseem.com/preseem-overview?hsLang=en#deployment-models)
- [Preseem Hardware](https://docs.preseem.com/preseem-hardware?hsLang=en#main-content)

    - [Legacy Hardware](https://docs.preseem.com/preseem-hardware?hsLang=en#legacy-hardware)
- [Installation & Activation](https://docs.preseem.com/installation-activation?hsLang=en)
- [Configuration](https://docs.preseem.com/configuration?hsLang=en)
- [Using Preseem](https://docs.preseem.com/using-preseem?hsLang=en#main-content)

    - [How to Use Preseem to Troubleshoot Subscriber Issues](https://docs.preseem.com/using-preseem?hsLang=en#how-to-use-preseem-to-troubleshoot-subscriber-issues)
    - [Operations](https://docs.preseem.com/using-preseem?hsLang=en#operations)
    - [How to Use Preseem to Optimize QoE](https://docs.preseem.com/using-preseem?hsLang=en#how-to-use-preseem-to-optimize-qoe)
    - [Preseem's RF Scoring and Metrics](https://docs.preseem.com/using-preseem?hsLang=en#preseems-rf-scoring-and-metrics)
- [Administering Preseem](https://docs.preseem.com/administering-preseem?hsLang=en#main-content)

    - [Upgrades](https://docs.preseem.com/administering-preseem?hsLang=en#upgrades)
    - [Planning and Configuration](https://docs.preseem.com/administering-preseem?hsLang=en#planning-and-configuration)
    - [Troubleshooting](https://docs.preseem.com/administering-preseem?hsLang=en#troubleshooting)
    - [User Management](https://docs.preseem.com/administering-preseem?hsLang=en#user-management)
- [Integrations](https://docs.preseem.com/integrations?hsLang=en)
- [FAQs and Other Explanations](https://docs.preseem.com/faqs-and-other-explanations?hsLang=en)
- [Amplify AI - Support Assistant](https://docs.preseem.com/amplify-ai-support-assistant?hsLang=en)

- [Aterlo Blog](https://preseem-467307.hs-sites.com/blog)

[![Chill listening crop-3](https://docs.preseem.com/hs-fs/hubfs/Preseem_logo_large.png?width=80&height=30&name=Preseem_logo_large.png "Chill listening crop-3")](https://preseem.com/)

Copyright © 2026, Preseem (Aterlo Networks)